Translate

Saturday, October 17, 2015

Charging up my solar heating system

South end of my workshop showing 4 solar collectors
It is mid October and we have had our first few frosts here in Maine and they had a few inches of snow in western Maine yesterday.  This means that it is time for me to fill the solar collectors on my workshop heating system with antifreeze.  The heating season lasts until mid-May here and in the winter temperatures rarely get above freezing for up to three months.  My workshop building is super insulated and I heat it with a combination of solar, propane and a wood stove.  I use a cord of wood that I cut and split myself from my backwoods to heat the downstairs area, keeping it around 60°F and higher if I am actively working in the space.  I use the solar/propane primarily to heat my second-floor office where I am more sedentary and set the temperature around 70°F or so during my working hours.


Pumping a bucket full of antifreeze into the collectors
To fill the collectors, it takes around 6 gallons of 50% Dow Frost antifreeze.  I use a small electric pump and hoses to pump this fluid into the system and pressurize it to 10 psi.  It takes a while to eliminate all the air bubbles from the system so I leave the pump circulating for a while to push the bubbles out of the plumbing and collectors.
DTC-D Solar Differential Temperature Controller
Once the system is filled, I connect the 3 small solar panels on the roof to the Differential Temperature Controller that I designed and manufacture (shown above).  This device monitors the temperature of the collectors and the storage tank and only activates DC circulation pumps when the collector is hotter than the storage tank by at least 10°F.  Powering the circulation pumps directly from solar panels guarantees an efficient and reliable heating system.

You can see live performance charts and gauges of my heating system on this page of my website.  On a good sunny day in the winter the system can raise the 80 gallon storage tank temperature by over 40°F.  The stored heat is then fed to baseboard radiators at night as needed.  If the stored water temperature drops below 140°F a Bosch Aquastar boiler automatically makes up the difference to ensure that heating water is always delivered to the radiators at 140°F.

Tuesday, September 29, 2015

Unsustainable tech product packaging


Linx evaluation kit - case not to scale
For the last 40 years or so I have been designing and developing electronic products.  Many of these products incorporate short range radio controls, and this has become a specialty of mine.  For the last 20 years or so I have been working with a company called Linx Technologies that make a broad line of miniature radio chips and antennas that are ideal for small products.  When they introduce a new product I sometimes order an evaluation kit from them that typically costs around $100.  These kits include battery-powered demonstration circuits that help to familiarize you with how they work.  

Linx have just released an exciting new radio product that I plan to use in a project I am currently developing so I ordered the relevant evaluation kit (see their promotional image above).  In the past, these kits were shipped in small custom fitted cardboard containers and it was quite simple to recycle the cardboard materials.  Not so with this newest kit that came in an aluminum case that weighs almost 3 pounds and measures 14" x 10" x 4".  I was stunned when the package arrived because it was so huge and heavy.  The distributor (Digi-Key Corp.) packed it in sustainably sourced paper packing material that can be recycled, but I have no idea what I am supposed to do with this large metal case.  I do not need to clutter my home office with this albatross, and will simply store the components on a shelf.  Here are is a picture of the relatively tiny (and not very fragile) parts inside the case:
Kit with all parts visible
I find the idea of shipping small items weighing only a few ounces in a 3 pound case to be completely offensive to my sensibilities as someone committed to living sustainably.  From my perspective this is a 1950s style Mad Men style promotional concept that has no place in today's world and it made me angry.  I also have to question the 1 pound stack of documentation that came in the kit.  While it is convenient to have paper manuals, technology companies do not commonly send any paper documentation with their samples since everything an engineer needs to know about their products is available from their website.  15+ years ago I used to have bookshelves filled with thick technical manuals, but they have all disappeared in favor of PDF documents readily available on corporate websites.

My small rural town recently switched to a Pay As You Throw (PAYT) program which requires our trash to be placed in specially purchased orange trash bags that cost $1 for a small bag and $2 for a large bag.  The purpose of this program is to incentivize increased recycling in our town and I am hoping it will have the desired effect.  Currently the town recycles around 20% of its waste stream, while I am averaging 60%.  The impact of the new program on me is that I resent companies that send me products packaged in bulky non-recyclable materials.  I have conveyed my displeasure to the sales person I work with, and he says he will talk to the marketing department at his company about my concern.

There are so many companies that are embracing social responsibility on so many levels that it makes me sad to see a good company that ignores the realities of a planet with finite resources.

After seeing this blog post, the Linx salesman that I work with offered to pay for return shipping of the offending metal case via FedEx.  I appreciate his thoughtful response to my displeasure.

A friend saw my blog and has asked if he can have the case.  Giving it to him has a lower carbon footprint than shipping it back across the country.  Everybody wins!

Friday, September 25, 2015

Sustainably sourced dining room chairs

My wife and I have separated after 20 good years and she has moved back to California where we first met.  It is an amicable separation but nonetheless she ended up taking a lot of furniture and other essentials with her.  This left me without a set of dining chairs.  Ideally I wanted chairs that were sustainably sourced in some way.  My original thought was to approach my friend and neighbor, John who is a skilled furniture maker because he had recently made a really stunning set of craftsman style chairs for his home.  But he explained that it would take up to a week per chair to make them even if I was helping and I realized I had neither the time or the money to invest.

My next step was to go to a local furniture store that represents Amish furniture makers.  They had a variety of samples that I found quite suitable for my needs at prices ranging from $230-$265 per chair and this was the upper limit for my budget.  The problem was that it would take 6 to 8 weeks to have the chairs made.  At this point it occurred to me that I really do not need heirloom quality furniture since I have no children or heirs who may wish to inherit furniture from me.  Also I did not want to wait that long because I had decided to convert the guest room in my house to a B&B using airbnb and wanted to get that set up pretty quickly.  Click here to see my listing, I have already had a few guests and I am getting reservations for the fall color season here in Maine which peaks in mid October. (We refer to the out-of-state visitors who come for the fall as "leaf peepers"). 

So finally I resorted to searching for chairs on the web and found a nice set of chairs from Sears.com on sale for under $50 each.  While I was not particularly comfortable with the idea of chairs that are made in Malasia, I did learn that they were made from "sustainable rubber wood".  In doing my research I learned that rubber wood has come into usage in the last few decades as a secondary use for trees from rubber plantations.  When these trees reach the age of around 30 years, their production diminishes and they  are harvested for their wood and the plantation is replanted.  The wood itself is prone to infestations from beetles, but when treated properly and dried correctly it can look somewhat like mahogany.  It is an attractive hardwood that takes stain and finish very nicely.

The chairs arrived at the local Sears store in a few days partially assembled in flat boxes.  Assembly was surprisingly simple and easy and I was impressed with the quality of the finish and the engineering of the joinery that makes for a very sturdy chair.
Chair parts
First chair assembled

The chairs did not take long to assemble, and look good with my family heirloom Jacobean reproduction oak table from England.
Whenever I need to purchase anything, I recognize that I am voting with my dollars for - or against - a sustainable future for humanity.  I take every decision quite seriously, particularly when dealing with large items.  But this also scales down to purchasing food at the local grocery store, natural food stores, and farmers market.  I make every effort to support local agriculture or acquire foods that are not shipped in from another country.

Thursday, September 10, 2015

Low cost to operate night lights

Here in rural Maine there are no streetlights or reflected city light at night so it gets DARK at night.  This means that when the lights are out inside the house it can be difficult to navigate to the bathroom or kitchen.  So for this reason I have liberally sprinkled nightlights throughout the house to make it easy to get around without having to turn on  lights.  
7 W night light
The classic old-style standard 7 W light bulb style nightlight has been obsolete for several years and I personally have never used them but I did the math and calculated that if you are paying $.10 per kilowatt hour (which is about average) for electricity, each one of those old light lights would cost over six dollars a year to operate which is more than many of them cost to purchase new off-the-shelf!  if you happen to have one of these dinosaurs in your home, I encourage you to discard it immediately and upgrade to the newer technologies.

In the past I have purchased three packs of electroluminescent nightlights for around $10-$12 and they tend to last several years before they eventually grow dim and become relatively useless.  I tested one of these lights and found that it draws .033 W for an estimated cost of about 2.5 cents/year.  A few days ago I was in the hardware store and saw a two pack of blue LED nightlights selling for under nine dollars and thought I would try them out.  LEDs draw a little more power at .125 W for an operating cost of around $.10/year.  LEDs are typically rated to last 30,000 to 50,000 hours so I expect these to last 3 to 5 years.

Here are some comparison images of LED (top) and electroluminescent (bottom)  with ambient lighting and lights out:
LED vs electroluminescent night light in ambient light

LED vs electroluminescent night light in the dark
The LED is significantly brighter and cast a visible pool of light in a dark hallway, while electroluminescent ones are just enough to see by, similar to moonlight coming through a window.

There are other types of night lights that contain light sensors and motion sensors so they turn off when they are not needed.  I suspect that those that use a motion sensor consume a fair amount of power even when they are off just to maintain the motion sensor.  (they do, see this blog post).  I leave mine on all the time since their cost to operate is so trivial.

Another small repair

This beautiful polished metal torchiere lamp was damaged a few years ago at the point where two of the sections of the main column screwed together.  It has been limping along for a while and I decided to repair it to use in my spare room which I will be renting out as an airbnb room soon.  Shown above is the repaired lamp that has been fully retrofitted with LED lamps.

The repair was relatively simple for me as a woodworker.  I cut a strip of ash and then milled out slots to create a "splint" for the bottom half of the lamp column.  Here is the before picture:
And a close-up of the wood channel that I made:
 Which I glued on around the column:
Works like a charm!

From a sustainability standpoint this is another large, heavy item that did not make it to the landfill.  Plus it saved me the expense of purchasing a new lamp!
 

Thursday, September 3, 2015

A thinner wallet can be a good thing!

A few years ago I decided that my wallet had become too thick.  It contained the usual assortment of cards including driver's license, library card, debit and credit cards and also half a dozen rewards cards.  So I decided to do something about it.  I scanned in the face of all of my rewards cards, and then scanned the bar codes on the back and then tiled them all together in Photoshop:
I scaled the bar codes as large as practical and have never had a problem with them scanning at the cashier.  After I printed out the card, I covered both surfaces with 2 inch wide clear packing tape to protect it.

Now when a cashier asks me for my rewards card, I offer them the card and isolate the bar code they want to scan between my fingers so the scanner does not get confused by reading the wrong bar code.  A number of cashiers have complimented me on my clever idea so I thought I would share it with my readers.

Chiropractors are aware that sitting on a thick wallet can contribute to a whole host of issues ranging from scoliosis to neck pain, and I certainly feel more comfortable now that it is nearly 1/4 inch thinner.

* A reader just commented that there is "an app for that" called Stocard.  I personally don't use a smart phone, but this seems very useful.  Not sure where most folks carry their phones, but if it's in their back pocket, they will still have back health issues.

Saturday, August 15, 2015

It's Brush Hog Day!

My 2.5 acre rural lot here in Maine is mostly wooded and the front half acre or so is divided between lawn areas and open field where I let the weeds grow.  I maintain the lawn with my solar powered lawnmower.  At this time of year the Goldenrod and other tall weeds are over 4 feet tall so I hire a neighbor with a brush hogger to cut everything back.  This also helps to fight back the tide of saplings encroaching from the woods.  If left uncut the entire property would be overgrown with tall trees within 10 or 15 years.  My neighbors on each side both have much larger lots of 10 acres or so each with open fields.  One neighbor brings in a crew to hay and bale his field while the other just cuts it back as I do.

Opening up the field gives us better access to the burn pile.  This is a pile of tree branches and saplings that I clear throughout the year.  Some neighbors wait until the pile is many times the size of ours and have a big bonfire when the snow is on the ground.  I like to keep my burns smaller and more manageable so I light them two or three times a year in the spring and fall.  
Last year I lit off the burn pile before it was brush hogged, and even though I mow a circle around the burn pile, it made for close quarters while maintaining the fire.  I think I will wait until the weather is cooler before burning this pile, it is way too hot and humid.

I enjoy being outside and actively maintaining my property throughout the year, it is good exercise and keeps me in touch with seasonal changes on the land.

Thursday, August 6, 2015

Bumper crop of fruit

The previous owners of my property had planted 4 high bush blueberry bushes, and numerous fruit trees about 20 years ago.  I have carefully pruned and maintained the blueberry bushes and pick as many as 5 or 6 gallons of blueberries a year, this year I have a bumper crop, and the branches are bowed down with berries.  It is hard to keep up and I have invited the neighbors to come and help themselves.
 
These are large, sweet blueberries and it is hard to resist eating them while picking!  I also had to deploy a small electric fence around them to keep the wild turkeys and deer from devouring them.  There is a flock of a dozen or so chicks with three or four hens that come around almost daily scavenging what they can.

The apple tree had been producing a moderate number of small sweet cooking apples over the last few years, but this year there are literally so many apples on it that the weight has bowed the branches down to the ground and it has collapsed over my firewood pile.
On closer inspection I realized that this largest main branch has actually broken off at the trunk and I will have to cut it off.  I hope it survives long enough to yield fully ripened apples.
Talk about going out with a bang!  Perhaps I should have been more proactive the pruning for this tree but it is impossible to anticipate a bumper crop of apples like this.

I really enjoy the seasonal cycles here in Maine, the growing season so very visible and tangible because is so short here.  Any day now they will start to cut the 50 acre hayfield across the road from our house and that is always an interesting process to watch.

Wednesday, July 22, 2015

Who killed the vampire loads loads in my entertainment system?

In a recent post I wrote about replacing my dead 37" LCD TV with a new 50 inch unit.  I didn't realize I was buying into an entirely new AV ecosystem.  I got talked into purchasing a sound bar for the TV which completely replaced my old-style stereo amplifier that I originally used for the sound system for my TV.  So I have completely restructured my entertainment system and in the process I have taken detailed measurements of its power consumption using a Kill-A-Watt meter.  The biggest take away I have gotten from this experience is that over the last 10 to 20 years new appliances have dramatically reduced their phantom loads.  A phantom (or vampire) load is the power an appliance consumes when you think it is "off".  In an entertainment system this includes all of the devices that you can turn on remotely.  They have an internal circuit that sits there all day waiting for a signal from your remote control and that consumes a certain amount of power - sometimes several Watts.

My original entertainment system consumed around 9 W in standby mode not counting the DVR and I used a timer to turn everything off from midnight to 6 PM thus reducing the load to the timer itself which is only 1 W:
My new entertainment system is significantly more efficient, not only when everything is on, but also when all of the devices are turned off.  My Kill-A-Watt could not get a valid reading for the TV, sound bar or Fire TV (streaming video) box because it is below its measurement threshold of 1 W.
I have recycled the DVD player, stereo amp, and CD player because I no longer need them.  The new sound bar lets me play my music via Bluetooth from my tablet or from the cloud using the Fire TV, and who uses CDs anymore these days?  So now my power consumption when watching TV has dropped from 223 W to around 102 W.  A 50% reduction.  Here in Maine we pay approximately $.14 per kilowatt hour, and if we assume I watch TV for five hours a night which is considered average then the monthly cost drops from about $4.68 to $2.14.  So I am saving over $2.50 on my electric bill every month.  (Actually I don't pay for electricity during the summer months because my solar array generates a surplus!).  If you extrapolate this across all the entertainment systems worldwide, this energy savings is really significant.

By the way, in the process of setting up and configuring the new TV, I learned that by adjusting the brightness setting I could reduce its power consumption from around 73 W down to around 50 W without any significant compromise in image quality.  You may want to dig into the settings on your TV and see how low a brightness setting you find acceptable.  If you do this while the TV is plugged into an energy meter, you can balance brightness versus power consumption.  It may take a period of adjustment to get used to a slightly less bright TV, but the default settings are usually much brighter than is necessary.

I think the drop in power consumption has a lot to do with advancing technology, but also some push back from consumers who want more efficient appliances.  Over the last several decades televisions have dramatically improved their operating efficiency as they transitioned from old-style CRT tubes to cold cathode backlit LCD screens to LED backlit LCD screens.  Similarly, engineers have found a way to reduce those pesky vampire loads in the entertainment systems.

So if you are overcome by "consumer-itis" and decide you need to upgrade your entertainment system, you may find that your electric bill drops significantly while your viewing experience is enhanced.  Guilt free TV! - who knew?  Just don't forget to recycle your old equipment.

Monday, July 20, 2015

My artwork that inspired an Invention that became a successful Business

I am going to start by going off topic for this post and tell you about a surprising success I had back in 2002.  At that time I was making turned wood artworks that took the form of undulating shapes supported by legs.  I have sold most of those pieces, but here is a good example:
"Ground Effect" by Guy Marsden
These artworks created a sense that the central lighter colored piece of wood was floating and eventually I decided that I  wanted to create a piece in which the wood actually levitated.  The result was this piece:
"The Mother And Child Reunion"
by Guy Marsden
(this piece is available)
The large yellow "mother" section is actually attached to the tusk shape in the back, while the smaller "child" element hovers just below:
"child" suspended in thin air!
The "child" moves around slightly in air currents but remains about a quarter inch away from the upper section at all times.  When I decided to embark on this project I researched magnetic levitation and eventually decided to develop my own circuit that would accomplish the levitation for this artwork.  (I design electronic products for a living: http://www.arttec.net/Industrial/Design.html). There is a small powerful magnet embedded in the lower section, and an electromagnet with control circuitry that I designed in the upper section.  It took me about two weeks of research and development to come up with an ideal circuit.

Having completed the artwork, it occurred to me that other electronic hobbyists might enjoy building the circuit that I came up with.  So I approached the hobby electronics magazine: "Nuts and Volts" to see if they would like me to run a construction article.  They approved enthusiastically and my article was published in 2003.  

Authors who publish construction articles often offer a kit of parts along with a circuit board and instructions to make it easier for people to build their design.  So I designed a circuit board, ordered parts and created instructions comprising a total investment of around $500.  I hoped that I would sell several dozen kits over the next few months after the article was published.  Here's a photo from the article showing the original kit levitating a matryoshka doll:
Original levitation kit assembled
I was quite surprised by the response to my kit and in my first full year I sold over $9,000 worth of them!  It was delightful that my email inbox went from: "you've got mail" to: "you got money" as order confirmations came in via PayPal.  Since then, sales have tapered off somewhat but I still sell several thousand dollars worth of them every year through my website: http://www.arttec.net/Levitation.  I offer kits and fully assembled versions and often hear from people that have made amazing projects with the kit - like this wonderful flying bird:
click here to see more projects
I often look back and reflect on the unusual sequence of events that began with creating an artwork that transitioned to designing an electronic circuit that became a successful product.  I think the lesson to be learned here is to always be open to the possibilities and to recognize and take advantage of every opportunity that presents itself.

To bring this blog post back around to the topic of sustainability, a few years later this experience inspired me to market another product that I originally designed for my own personal use.  This is a solar differential temperature controller used to improve the performance of my off-grid solar thermal heating systems.  I was equally surprised at how easy it was to start the business and how successful it became - I guess I have a knack for starting small businesses.  I eventually developed more sophisticated versions of this basic product and market them from a separate website: http://ArtTecSolar.com/
ART TEC SolarSolar Differential Temperature Controllers
There are now hundreds of my products out there in the world improving the performance of off-grid solar heating systems and I feel good that I am making a contribution to this important renewable energy market segment.